tenon造句

The tenon does not conform to the mortise, so it can not fit into the mortise.
榫头得大小和卯眼不相符，无法落槽。

Oblique tenon was adopted to draw core due to the short distance of drawingcore.
由于抽芯距离短, 采用斜销抽芯。

Analysis of Forming Defects in the Forging Process of Blade with a Single Tenon.
单榫头叶片锻造过程成形缺陷分析

Keywords Blade with a tenon Precision forging Forming laws Numerical simulation.
单榫头叶片精锻成形规律数值模拟

Footboard and horizontal stroke board coupling is used cylindrical tenon hammer.
竖板与横板的联结采用圆柱形榫钉。

Hydraulic fluid power. Cylinder. Fork yoke and tenon for extremity of piston rod.
液压传动。千斤顶。塞杆端部用内螺纹普通定位销和支座

Design of the inner circle machining clips for static blades tenon of gas expander
烟机静叶片通用车内圆榫头夹具设计

Combined Operation of Antiskidding Concrete Tenon and Grouted Retaining Stone Wall.
防滑混凝土凸榫与浆砌石重力挡土墙的联合运用

Mortise and tenon structure can withstandanail than furniture made of greater tension.
卯榫结构可以承受比用钉子做成的家具更大的张力。

Shell end mills with tenon and parallel key drive Part 0 Technical delivery conditions.
带横槽和纵槽的空心端铣刀。第2部分交货技术条件

The fixed unit is a fixed plate with a dovetailed tenon and a dovetailed tenon mortise.
固定构件为带有马牙榫、马牙榫槽的固定板。

Computer aided design on blade curve of obliquemounted wood working tenon milling cutter.
刀片斜装式木工榫铣刀刃口曲线计算机辅助设计

Keywords tenon edge bucklingobturation transportationshaping curingbondingsecondary curing.
榫边扣合密闭输送定型硫化粘合二次硫化

The production and optimized quality of tenon edge buckling duct obturation transportation belt
榫边扣合管状密闭输送带的制作及其质量优化

Milling cutters with tenon drive Interchangeability dimensions with cutter arbors Metric series.
榫传动铣刀。铣刀杆的互换性尺寸。米制系列

A fanshaped tenon that forms a tight interlocking joint when fitted into a corresponding mortise.
鸽尾榫嵌入榫眼形成紧扣在一起的接头

This thesis briefly introduces the design methods of the firtree tenon tooth accurate broach of turbine disk.
文中简要介绍了涡轮盘枞树形榫齿精拉刀得设计方法。

The antisliding function of tenon and its design theory were introduced in connection with a practical project.
结合工程实际，介绍凸榫得防滑机理及设计理论。

This paper studies Wood Tenoner Modeling and Computeraided manufacturing about numerical control tenon process.
本文研究实木榫建模与数控开榫计算机辅助制造技术。

in the traverse direction, the ligulate tenon of one floor is matched with the ligulate slot of the other floor.
在横向, 将一地板的舌形榫与另一地板的舌形槽配合。

Use four the hard mass alloy milling cutter, once to be milled on the section bar outing the correct tenon mouth.
使用四把硬质量合金铣刀，一次在型材上铣出正确榫口。

According to scholastic research, clear acting furniture is versed in at using tenon, do not beg exterior adornment.
根据学者的研究，清代家具工于用榫，不求表面装饰。

When in installation, in the longitudinal direction, the flat tenon of one floor is matched with the flat slot of the other floor
安装时, 在纵向, 将一地板的平榫与另地板的平槽配合

Furnitures drawer， must use the tenon to use the structural approach manufacture which again alternately the caking agent agglutinates.
家具的抽屉，必须用榫交叉再用粘接剂粘合的结构方法制作。

In my opinion, this is a dovetail structure joined together by a number of wooden bars, laths, brackets, mortise and tenon joints and rafters.
竹, 木, 石制器物或构件上利用凹凸方式相接处凸出的部分。