Moldin造句

a concave molding with a cross section that approximates a quarter circle
截面近于九十度弧的凹线脚

Technology of plate type steel castings produced by air impact molding line has been introduced AAR.
本文介绍了在气冲造型线上生产平板类铸钢件的铸造工艺。

A convex molding just below the abacus of a Doric capital.
多立斯柱头顶板下的凸出装饰。

We mainly used in chemical injection molding machines, accessories and screw cylinder.
我们主要是注塑机用的化工，配件及螺杆料管。

Each injection molding machine can achieve the most superior control effect.
每台注塑机都能达到最优得控制效果。

Sets goals for Molding department and employees and lead the team to achieve the objectives.
为注塑部及下属人员设立目标, 并领导团队达成目标。

In addition, the simple plastic molding process also can reduce the reject rate.
此外，简单的塑料成型工艺还能够降低废品率。

Keywords hurtle to cut the molding tool cleft choicemathematics modelfaintness synthesizes to adjudicate
冲裁模具间隙选择数学模型模糊综合评判

We adopt advanced multilevel soft cold extrusion processing molding, there are no chap and inner crack phenomenon.
采用先进的多级柔性冷挤压工艺成型，无龟裂内裂纹现象。

The ceiling is adorned with an elaborate molding around the edge, and features elements of the Seal of the President.
天花板上以总统印章为特征的图案被精心装饰。

The adornment style of technology molding metope and style are varied.
工艺造型墙面的装饰样式与风格多种多样。

The Company has advanced injection molding machine and plastic mold manufacturing equipment.
本公司拥有先进的注塑机和塑料模具制造设备。

Aerated concrete floor is cast molding of the necessary equipment.
底板也是加气混凝土浇注成型的必要设备。

Analysis of the Factors Affecting Inner Stress of Plastic Moldings
影响塑料模压制件内应力的因素分析

And the demoulding agent should be also noticed in the rotational foam molding.
同时，脱模剂在滚塑发泡工艺中也是值得注意的环节。

Study on Air Impulse Molding with Press Heads Pushed by Compressed Air
气冲气推多触头压实造型的试验研究

Air blowing injection molding machine
吹气射出成型机

The deformity of the columella, the dome, and the wide alar of the nose was significantly reduced following nonsurgical nasoalveolar molding.
鼻小柱延长及鼻塌陷畸形显著改善

Remove the backing from the tape, align the molding and position it on the body panel.
从胶带的背面拆卸，对准嵌条并且将它移至车体饰板上。

Add rose petals, press into molds, and allow to dry 23 hours before unmolding.
添加玫瑰花瓣，挤压入磨具，没有成型前晾干23小时。

molding allowance.
工艺补正量

Magnesium alloy diecasting molding, sturdiness and durability.
整车采用镁合金压铸成型，坚固耐用。

A medium modulus polyester alloy suited for injection molding of Air Bag Deployment Doors.
以中等模量聚酯合金适合注塑成型的气囊门。

By using mushy extrusion molding for magnesium alloy, the disadvantage of pressure casting is avoided.
采用糊态挤压成型镁合金避免了压力铸造的缺点。

accepting alteration , processing and manufacturing of plastic injection molding machines , extruders and barrel screws.
第十四条票据上的记载事项应当真实, 不得伪造, 变造。